勘误表

有关所有型号和配件的所有勘误表,请参阅 完整的 Zivid 勘误表 。

相机勘误表

Zivid 3

错误代码

概括:

版本:

E-39

Zivid 2, Zivid 2+ and Zivid 3 cameras stop responding on the network after receiving an Ethernet frame larger than 1526 bytes

---

Workaround: Set the MTU to 1500 on every network interface on the same subnet as the camera, including the PC that runs the SDK. On Linux, for example: sudo ip link set dev <interface> mtu 1500.

  • M70 Rev B3

  • M130 Rev A0

  • MR130 Rev A0

  • XL250 Rev A0

E-38

Capture hangs or fails on Intel GPUs when the application's OpenCL queue waits on an incomplete user event

---

Workaround: Upgrade to Intel Compute Runtime 26.40.40196.8 or later, where the issue is fixed.

If upgrading is not possible, complete every user event that the application's queue waits on before passing the queue to an SDK function or starting a capture.

  • M70 Rev B3

  • M130 Rev A0

  • MR130 Rev A0

  • XL250 Rev A0

E-35

在环境光闪烁的情况下使用采样间隔时,颜色图像偶尔会出现不一致(随机色调)

---

解决方法: 建议优先调整曝光时间,而非依赖采样间隔来减轻闪烁效应。如果必须使用采样间隔,则应实现一个重新捕获机制,以检测并校正受闪烁影响的彩色图像。

  • XL250 Rev A0

E-16

对于相同的硬件,Windows 上的捕获时间可能比 Linux 上更长。

---

解决方法: 锁定 GPU 核心和内存时钟速度可以减少捕获时间的波动(仅限 Nvidia GPU)。

  • M70 Rev B3

  • M130 Rev A0

  • MR130 Rev A0

  • XL250 Rev A0

E-15

Windows 上的捕获时间有时会更长(比正常情况长 1 秒以上)

---

解决方法: 增加 Windows 网络驱动程序设置中的 "接收缓冲区" 和 "传输缓冲区" ,以减少丢包的发生。

  • M70 Rev B3

  • M130 Rev A0

  • MR130 Rev A0

  • XL250 Rev A0

已解决的问题

错误代码

概括:

版本:

解决于:

E-37

投影仪的热稳定功能会导致亮度设置为 0 时 2D 捕获图像出现亮度波动。

  • M70 Rev B3

  • M130 Rev A0

  • MR130 Rev A0

  • XL250 Rev A0

v2.18.0

E-36

在某些 Zivid 3 XL250 相机上使用 2D 采样间隔设置时,捕获的 RGB 图像会出现严重的色彩偏差。

  • XL250 Rev A0

v2.17.2

E-34

在使用较慢的以太网连接进行全分辨率 HDR 捕获时,相机可能会重启

  • M130 Rev A0

  • MR130 Rev A0

  • XL250 Rev A0

v2.17.1

Zivid 2+

错误代码

概括:

版本:

E-39

Zivid 2, Zivid 2+ and Zivid 3 cameras stop responding on the network after receiving an Ethernet frame larger than 1526 bytes

---

Workaround: Set the MTU to 1500 on every network interface on the same subnet as the camera, including the PC that runs the SDK. On Linux, for example: sudo ip link set dev <interface> mtu 1500.

  • Rev A0

E-38

Capture hangs or fails on Intel GPUs when the application's OpenCL queue waits on an incomplete user event

---

Workaround: Upgrade to Intel Compute Runtime 26.40.40196.8 or later, where the issue is fixed.

If upgrading is not possible, complete every user event that the application's queue waits on before passing the queue to an SDK function or starting a capture.

  • Rev A0

E-16

对于相同的硬件,Windows 上的捕获时间可能比 Linux 上更长。

---

解决方法: 锁定 GPU 核心和内存时钟速度可以减少捕获时间的波动(仅限 Nvidia GPU)。

  • Rev A0

E-15

Windows 上的捕获时间有时会更长(比正常情况长 1 秒以上)

---

解决方法: 增加 Windows 网络驱动程序设置中的 "接收缓冲区" 和 "传输缓冲区" ,以减少丢包的发生。

  • Rev A0

已解决的问题

错误代码

概括:

版本:

解决于:

E-37

投影仪的热稳定功能会导致亮度设置为 0 时 2D 捕获图像出现亮度波动。

  • Rev A0

v2.18.0

E-34

在使用较慢的以太网连接进行全分辨率 HDR 捕获时,相机可能会重启

  • Rev A0

v2.17.1

E-33

GenICam/HALCON 中的点云看起来比 Zivid Studio 更暗

  • Rev A0

v2.14.0

E-32

使用 Halcon 时,在捕获一个较低分辨率的点云后,再去捕获一个较高分辨率的点云可能会失败(仅限 GenICam)

  • Rev A0

v2.14.0

E-30

导出的 PLY/PCD/XYZ 点云比 Zivid Studio 中更暗

  • Rev A0

v2.14.0

E-29

使用 Zivid::Experimental::Projection::showImage() 时,Zivid 2/2+ 可能会显示不正确的图像

  • Rev A0

v2.11.1

E-28

如果 PC 进程在捕获过程中中止,Zivid 2/2+ 可能会出现无响应/离线状态

  • Rev A0

v2.12.0

E-23

Zivid 2 上的固件更新在极少数情况下可能会因超时而失败

  • Rev A0

v2.14.0

E-14

捕获期间抛出 "CameraImageTimeout" 或 "Timeout" 异常

  • Rev A0

v2.14.0

E-10

如果 PC 进程在捕获过程中中止,Zivid 2/2+ 可能会挂起,导致 15 秒后重新启动。

  • Rev A0

v2.13.0

Zivid 2

错误代码

概括:

版本:

E-39

Zivid 2, Zivid 2+ and Zivid 3 cameras stop responding on the network after receiving an Ethernet frame larger than 1526 bytes

---

Workaround: Set the MTU to 1500 on every network interface on the same subnet as the camera, including the PC that runs the SDK. On Linux, for example: sudo ip link set dev <interface> mtu 1500.

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • L110 Rev A0

  • M130 Rev A0

  • M60 Rev A0

  • LR110 Rev A0

  • MR130 Rev A0

  • MR60 Rev A0

  • XL250 Rev A0

E-38

Capture hangs or fails on Intel GPUs when the application's OpenCL queue waits on an incomplete user event

---

Workaround: Upgrade to Intel Compute Runtime 26.40.40196.8 or later, where the issue is fixed.

If upgrading is not possible, complete every user event that the application's queue waits on before passing the queue to an SDK function or starting a capture.

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • L110 Rev A0

  • M130 Rev A0

  • M60 Rev A0

  • LR110 Rev A0

  • MR130 Rev A0

  • MR60 Rev A0

  • XL250 Rev A0

E-24

Zivid 2 恢复出厂设置按钮可能不起作用

---

解决方法: https://support.zivid.com/en/latest/support/reset-button-failure.html

  • Rev A0

  • Rev B2

  • Rev B3

E-16

对于相同的硬件,Windows 上的捕获时间可能比 Linux 上更长。

---

解决方法: 锁定 GPU 核心和内存时钟速度可以减少捕获时间的波动(仅限 Nvidia GPU)。

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • L110 Rev A0

  • M130 Rev A0

  • M60 Rev A0

  • LR110 Rev A0

  • MR130 Rev A0

  • MR60 Rev A0

  • XL250 Rev A0

E-15

Windows 上的捕获时间有时会更长(比正常情况长 1 秒以上)

---

解决方法: 增加 Windows 网络驱动程序设置中的 "接收缓冲区" 和 "传输缓冲区" ,以减少丢包的发生。

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • L110 Rev A0

  • M130 Rev A0

  • M60 Rev A0

  • LR110 Rev A0

  • MR130 Rev A0

  • MR60 Rev A0

  • XL250 Rev A0

已解决的问题

错误代码

概括:

版本:

解决于:

E-37

投影仪的热稳定功能会导致亮度设置为 0 时 2D 捕获图像出现亮度波动。

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • L110 Rev A0

  • M130 Rev A0

  • M60 Rev A0

  • LR110 Rev A0

  • MR130 Rev A0

  • MR60 Rev A0

  • XL250 Rev A0

v2.18.0

E-33

GenICam/HALCON 中的点云看起来比 Zivid Studio 更暗

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.14.0

E-32

使用 Halcon 时,在捕获一个较低分辨率的点云后,再去捕获一个较高分辨率的点云可能会失败(仅限 GenICam)

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.14.0

E-30

导出的 PLY/PCD/XYZ 点云比 Zivid Studio 中更暗

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.14.0

E-29

使用 Zivid::Experimental::Projection::showImage() 时,Zivid 2/2+ 可能会显示不正确的图像

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.11.1

E-28

如果 PC 进程在捕获过程中中止,Zivid 2/2+ 可能会出现无响应/离线状态

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.12.0

E-23

Zivid 2 上的固件更新在极少数情况下可能会因超时而失败

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.14.0

E-17

Ubuntu 20.04 和 Intel GPU 上的 "CL_OUT_OF_RESOURCES" 或 "OpenGL error:GL_INVALID_OPERATION" 的错误

  • Rev A0

  • Rev B2

  • Rev B3

v2.7.0

E-14

捕获期间抛出 "CameraImageTimeout" 或 "Timeout" 异常

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.14.0

E-10

如果 PC 进程在捕获过程中中止,Zivid 2/2+ 可能会挂起,导致 15 秒后重新启动。

  • L100 Rev A0

  • M70 Rev B2

  • M70 Rev B3

  • Rev A0

v2.13.0

E-9

Windows 上的 OpenCV 断言错误

  • Rev A0

  • Rev B2

  • Rev B3

v2.4.1