Connectivity and Power Supply

Connectors

../../_images/zivid-two-backside.png

  1. M12-5: Power Connector 24V, 5A DC

  2. M12X: Ethernet Connector CAT 6A

Check Zivid Approved Zivid Two Ethernet Cables for more information.

Factory reset button
../../_images/factory-reset-button.png

Reset (power cycle):

Intermittent press or hold for less than 5 seconds.

Reset to factory IP address:

Hold for 5 to 10 seconds until the Power LED turns green

Revert to factory installed firmware:

Hold for more than 10 seconds until the Power LED turns yellow.

../../_images/zivid-one-plus-backside.png

  1. USB3: Data

    SuperSpeed USB3 type-B receptacle for PC connection.

    Note

    PC must support USB 3.0 SuperSpeed.
    Cables need to be “USB3 Vision” compliant.
    Check Zivid Approved Zivid One+ USB Cables for more information.

  2. M12-5: Power Connector 24V, 5A DC

Power supply interface

Pinout

Pin

Purpose

power-supply

1

24V DC +/- 20% (Max 5A)

2

24V DC +/- 20% (Max 5A)

3

GND

4

GND

5

Reserved, do not connect

Optional mating connector: TE Connectivity AMP, 1838275-3 (Digikey: A97645-ND)

Tip

It is required to use both pins for 24V and for GND.

Data cable

Zivid Two uses a dedicated ethernet cable for data transmission. See Zivid Approved Zivid Two Ethernet Cables for more information.

The table below provides the Zivid Two Ethernet cable pinout.

Pinout

Pin

ethernet-interface

M12X-8

RJ45 (Color)

1

1 (WH/OG)

2

2 (OG)

3

3 (WH/GN)

4

6 (GN)

5

7 (WH/BN)

6

8 (BN)

7

5 (WH/BU)

8

4 (BU)

Zivid One+ uses a dedicated usb cable for data transmission. See Zivid Approved Zivid One+ USB Cables for more information.

Connecting to the computer

  1. Plug the power supply first into the “24V”.

  2. Plug the Ethernet cable into the camera and connect it to your computer.

  3. Plug the power supply into a power outlet.

Note

On disconnect, follow the procedure in reverse, disconnect mains power first.
Ensure that all connections are screwed in tightly. The coupling nut of the M12 screw connectors can in some cases be hard do screw in. However, when installed correctly they provide a robust and reliable connection.
Check System Requirements for performance considerations and review performance by observing the status Indication LEDs.

Use the AC/DC adapter supplied with the unit to ensure compliance with emission and immunity standards.

The Zivid camera is protected against reverse polarity and against overheating by a thermistor that physically removes the power.

The Zivid Two camera uses Ethernet communication and needs 10 Gbps for best performance. Your computer may not have a port for 10 Gigabit Ethernet. In that case, you can connect to it using an adaptor for 10GBASE-T (10 Gbps copper Ethernet) to Thunderbolt 3. At a reduced performance you can also use 1000BASE-T and NBASE-T (1 Gbps, 2.5 Gbps, and 5 Gbps over copper) to USB adapters.

Recommended network cards and adapters :color: light

We have successfully tested and recommend the following hardware:

Caution

USB-based network adapters have reduced and more variable capture speed, and can occasionally give errors when using the camera. Our recommendation is to use 10Gb PCI Express cards for optimal performance.

Warning

Use only Zivid approved Ethernet cables.

Network Topology

Zivid Two supports the following network topologies:

Direct connection

Connection via switch
../../_images/zivid-two-pc-direct-connection.png ../../_images/zivid-two-pc-connection-via-switch.png

Note

Multiple Zivid Two camera support added in 2.4 SDK.

Continue to Software Installation where you will also find Network Configuration.

  1. Plug the power supply first into the “24V”.

  2. Plug the Ethernet cable into the camera and connect it to your computer.

  3. Plug the power supply into a power outlet.

../../_images/zivid-one-pc-direct-connection.png

Note

On disconnect, follow the procedure in reverse, disconnect mains power first.
Ensure that all connections are screwed in tightly.
For more details see: Failed to Locate 2D Camera With Serial Number.

Use the AC/DC adapter supplied with the unit to ensure compliance with emission and immunity standards.

The Zivid camera is protected against reverse polarity and against overheating by a thermistor that physically removes the power.

Caution

Using a direct cable from the PC to the Zivid camera works better than connecting the camera via a USB hub.
Use only Zivid approved cables and extenders.

Continue to Software Installation.